1, outlines This factory manufacture's YKM-6 electric cable hauling is the electric power, the petroleum, the chemical industry, chemistry, the industry newly built, expands the power plant, laying of cable's and so on transformer substation one kind of new machineries, it is suitable for any form electric cable bridge, in the electric cable trench lays each kind of power electric cable and the control cable, uses this equipment fundamentally to change the artificial laying of cable's phenomenon, when may save large quantities of labor placing, can raise the economic efficiency, thus, this equipment lays a batch electric cable more ideal machinery. The practice proved that uses the YKM-6 electric cable traction machinery not to be able correctly to create the cable insulation damage, for the machinery normal operation, reduces the breakdown, the extension service life, please careful reading this explanation.
3, machinery building block YKM-6 electric cable traction machinery by: Tractor (10), cable drum support (2), pulley (100), lead block (20 groups), electrical control bench () and so on compositions. (1) tractor The tractor is laying of cable's major installation basically by, about the transport mechanism, the electrically operated gear box, the compaction organization, the accent card organization, Lian Lun, the plow belt, the support shell and so on composes. (2) pulley The pulley mainly uses in the brace holding the electric cable, reduces time laying of cable's friction force, the pulley organization may fix conveniently on the cable holder or may place at will the ground, cannot be fixed. (3) lead block The lead block, uses in the turning point electric cable guidance, and guaranteed the electric cable bevelling radius in permits in the scope. (4) cable drum support The cable drum support is the mechanical structure, picks up or the landing electric cable line depending on lead screw's fluctuation, but load-bearing 7 tons. (5) control bench The electrical control bench is the electrically controlled major installation, may simultaneously control 10 tractor's advances, the backlash, the stop movement, and is loaded with the audible signal device.
In the laying of cable process may carries on whole set unit revolution on the control bench or any tractor (advance, backlash) and the stop operation, on various tractors' change-over switch (ZHK), may initialize the tractor plow belt's rotation direction. This aircraft is equipped with the short circuit protection, when kicks return route's any spot has the short circuit, the automatic air switch can automatically trip, separates the total power source. This aircraft has also been equipped with the load protection, when any electric motor load, sends out the electric bell sound in the control bench, has the humming sound in this tractor place, and entire line automatic stopping movement.
l, the basis electric cable bridge, the electric cable trench's form and the route, the arrangement and the fixed good tractor, the tractor imposition should with the electric cable in the support level unidirection, be advantageous for a row of electric cable, and installs the pulley in the relevant position, between each tractor the gap may decided according to the hauling mechanical computed result and the scene situation, according to - the experience considered, may take in 45 meters, between two tractors the gap may be supposed an every 1.5~2.5 meters about pulley, to reduce electric cable withstanding the lateral pressure, the corner, the import should arrange a tractor, turns round the spot according to the electric cable permission bevelling radius arrangement lead block (the approximately 2 groups). 2nd, chooses the good laying aside control bench the position, earths reliably the outer covering, then meets the power source coil in (its section not to be smaller than 3×6+1×4), then tries the movement in the control bench (not to drive tractor), operates the advance separately, stops, retroceding the button, the movement is unmistakable, then separates the total power switch. 3rd, the survey power and operates return route's dielectric resistance, generally is not smaller than 05MΩ tractor's on change-over switch ZHK, sets “the stop” the position, inspects tractor's mechanical condition by Taiwan, should be good, does not have the card astringent or other abnormal phenomena, closes in the control bench the total power switch and the console switch, then tries the movement on the tractor. 1) will transform the day to close ZHK to put in “the clockwise” (or “reverse”) the position, according to the advance button, the tractor plow belt rotation, its direction should probably the direction of advance with the electric cable to be consistent, then according to the pause button, the tractor plow belt stops the transmission, and the tractor place sends out the sound signal in the control bench. 2) according to the backlash button tractor plow belt toward the reverse direction rotation, according to “the stop” the button, the tractor plow belt stops the rotation, and the tractor place sends out the sound signal in the control bench. 3) carries on according to the above method when the electric drive experiments and confirms is unmistakable, then about plow belt between the distance adjusts, causes it slightly is smaller than the electric cable diameter, prepares is operational. 4) will spread the electric cable to transport to assigns the position, on the slippery wheel disk support, moves nimbly with the hand plate is the standard. 5) the preparatory work ready then starts the laying of cable, starts when lays, from the human the first electric cable pulls to the first tractor nearby, starts the tractor, penetrates between the plow belt electric cable, electric cable along with plow belt's rotation. Proceeds the movement, when after electric cable puts on the tractor. May place on the pulley, pushes before the tractor courses.
1, everything exposes in the outside rubbing surface, the rotation spot.
2, this aircraft gear box, the gear box and the bearing, a half year note butter one time, after each project finished at least, must repair - the time.
3, when the discovery tractor revolution is not normal, should immediately the shutdown check, after the trouble clearing, only then uses.
1. before the tractor starts, must according to “the stop” the button, in the control bench send out the sound signal, gave advance notice that the control bench operators prepare the start.
2. when any tractor does not rotate, should loosen the holding apparatus immediately, refuses, in does not loosen the holding apparatus in the situation, pulls the electric cable, in order to avoid causes the electric cable withstanding pulling force to be oversized and damage machinery.
3. lays several electric cables after every time, must inspect various spots promptly the bolt whether to become less crowded, avoids various spots joint not being good.
4. refuses in the charged situation, or draws out the attaching plug insertion, in order to avoid has the danger.
5. when transportation or transporting, refuses to fall, to pound the tractor control bench and the power line.
6. in any situation, does not allow simultaneously to direct to deliver two or two above electric cables.
7. before the use, must certainly regulate the single plane gear box's speed to keep off the position to be unified.
Detail Description